| |
| Drawing on the heritage of Australian Monitor’s
low impedance amplifier design comes the latest in low
impedance amplifiers from the Australian Monitor Pro series,
the Synergy2. The Synergy 2 series offers an impressive range
of highly powerful 2 Ohm rated amplifiers in rugged yet
stylish 2 RU chassis. Available in three powerful models the
SY2200 will deliver 600W, the SY2400 will deliver 1100W and
the SY2700 will deliver 2000W. All models also offer on board
clip limiting, ground lift switching, XLR ins and binding post
and 4 pole speaker connector outputs. As with all Australian
Monitor Pro Series amplifiers they deliver the sonic clarity
you’ve come to expect from an AM
amp. |
|
|
| |
SY 2200 |
SY 2400 |
SY 2700 |
| Output Power &&
2 Ohm |
2 x
300 watt |
2 x
525 watt |
2 x
1000 watt |
| (0.1% THD@1kHz) 4Ohm |
2 x
200 watt |
2 x
350 watt |
2 x
700 watt |
| (0.1% THD@1kHz) 8Ohm |
2 x
110 watt |
2 x
190 watt |
2 x
400 watt |
| 8 Ohm Bridged |
400 W
|
700 W
|
1400
W |
| 4 Ohm Bridged |
600 W
|
1100
W |
2000
W |
| Voltage Gain |
28.3
(29 dB) |
37.4
(31 dB) |
52.9
(34 dB) |
| Thermal Dissapation |
Both
channels driven, 2 Ohm load, 1/8th power 425W
(1450btu/hr) |
Both
channels driven, 2 Ohm load, 1/8th power 780W
(2661btu/hr) |
Both
channels driven, 2 Ohm load, 1/8th power 1410W
(4811btu/hr) |
| Current Draw |
Both
channels driven, 2 Ohm load, 230 V AC, 1/8th power, 2.7A
|
Both
channels driven, 2 Ohm load, 230 V AC, 1/8th power, 5.0A
|
Both
channels driven, 2 Ohm load, 230 V AC, 1/8th power, 9.1A
|
| Dimensions (HxWxD) |
87 x
482 x 400 |
87 x
482 x 400 |
87 x
482 x 455 |
| Unit Weight |
12.5
Kg |
15.5
Kg |
17.5
Kg |
| Shipping Weight |
14 Kg
|
17 Kg
|
19 Kg
|
| Shipping Dimension |
210 x
540 x 540 |
210 x
540 x 540 |
210 x
540 x 575 | |
COMMON
SPECIFICATIONS
| Distortion (re 4 Ohm, -1dB below
clip) |
2 x 300 watt |
| THD (@ 1 kHz) |
<0.02% |
| IMD SMPTE (60 Hz : 7 kHz 4:1) |
<0.03% |
| Input Impedance |
20
kOhms |
| Input Sensitivity |
1
Vrms |
| Input CMRR |
>80 dB |
| S/N Ratio A-weighted |
>
104 dB |
| Crosstalk |
>
70 dB |
| Slew Rate |
>
40 V/usec |
| Damping Factor (@ 1 kHz re 8
Ohm) |
>
375:1 |
| Frequency Response (+/- 3 dB) |
15 Hz
~ 50 kHz |
| Indicators |
Power, Status (L/R), Overload, Thermal,
Fault | |
| |
